User Login    
 + Register
  • Main navigation
Login
Username:

Password:


Lost Password?

Register now!
Fast Search
Slow Search
Google Ad


[Datsun 1200 encyclopedia]

6-speed

(Difference between revisions)

Datsun 1200 encyclopedia | Recent changes | Switch to MediaWiki mode

Printable version | Disclaimers | Privacy policy | Current revision
Category: Transmission

Revision as of 07:06, 2 January 2012
ddgonzal (Talk | contribs)
(->S15 6-speed)
<- Previous diff
Revision as of 07:08, 2 January 2012
ddgonzal (Talk | contribs)
(->S15 6-speed)
Next diff ->
Line 4: Line 4:
The 1999-2002 Nissan [[Silvia]] S15 Strawberry with SR20DE/SR20DET had an optional close-ratio 5-speed + overdrive (6 forward speeds total). In AUS, the six-speed was in the Nissan 200SX Spec-R model. The 1999-2002 Nissan [[Silvia]] S15 Strawberry with SR20DE/SR20DET had an optional close-ratio 5-speed + overdrive (6 forward speeds total). In AUS, the six-speed was in the Nissan 200SX Spec-R model.
-Like most Nissan RWD transmissions, this is made by [[Aisin]]. The basic Aisin AZ6 gearbox was made in three versions, with front cases for these engines:+This gearbox is made by Aisin. The basic Aisin AZ6 gearbox was made in three versions, with front cases for these engines:
* Nissan SR20DET (S15) * Nissan SR20DET (S15)
* Mazda Renesys (RX8 rotary) * Mazda Renesys (RX8 rotary)

Revision as of 07:08, 2 January 2012

6-speed transmission gives you two (count 'em 2) overdrive gears. Or some have a close ratio direct-5th with overdrive, which is better for performance. 6-speeds can be modified to fit Datsun 1200. Just cut the bellhousing and weld on a fragment of A-series bell housing, then machine the input shaft smaller.

Contents

S15 6-speed

The 1999-2002 Nissan Silvia S15 Strawberry with SR20DE/SR20DET had an optional close-ratio 5-speed + overdrive (6 forward speeds total). In AUS, the six-speed was in the Nissan 200SX Spec-R model.

This gearbox is made by Aisin. The basic Aisin AZ6 gearbox was made in three versions, with front cases for these engines:

  • Nissan SR20DET (S15)
  • Mazda Renesys (RX8 rotary)
  • Mazda F & B (S2000 and 2001 MX-5)
  • Toyota 1G, 3S (SXE/GXE10 Toyota Altezza & Lexus IS)


S15 modified; A-series bell grafted on
19983.jpg

  • FS6R92A
  • only 16kg heavier than a standard 1200 4spd
  • Close ratio 1-5, with overdrive 6th. It is perhaps the best ratios for an A-series engine

Gear Ratios

  • 1st: 3.630
  • 2nd: 2.200
  • 3rd: 1.543
  • 4th: 1.210
  • 5th: 1.000
  • 6th: 0.767

Pilot Bushing

S15 5-speed FS6R92A

  • 32202-B9500 BUSHING-CRANKSHAFT
  • used on L, Z, VG, VQ, SR, KA, and CD engines (same as 71C bushing)
  • Pilot Bushing Inside Diameter: 0.626 to .6300" (Length: .689")
  • Pilot Bushing Outside Diameter: .814 to .815"

Since this is much larger in diamter than the A-series, machining is needed.

A-series crankshaft bore is for a bushing with 0.671" O.D., length .723"

  • The FS6R92A input shaft end can be turned down to ~.671 O.D.
  • Could the A-series crank pilot hole be bored out to .814" so the 71-Series bush can be fitted?


Clutch Disc

FS6R92A clutch disc [all 240mm]

  • 30100-85F00 9901-0011
  • 30100-85F14 0011-
  • Spline O.D.: 1"
  • Spline: 24 teeth

There is an A-series clutch disc that is 1" x 24T: 30100-K0500.

Input Shaft Length

How far does the FS6R92A input shaft extend past the transmission face?

  • 5-speed: about 17mm past the flange
  • 6-speed: about 10mm inside the flange

Speedometer

S15 6-speed does not have a speedometer gear.

Clutch Release

How to connect up the clutch?

Gearshift Location

Rear Crossmember

Propeller Shaft