User Login    
 + Register
  • Main navigation
Login
Username:

Password:


Lost Password?

Register now!
Fast Search
Slow Search
Google Ad


[Datsun 1200 encyclopedia]

Fuel tank

(Difference between revisions)

Datsun 1200 encyclopedia | Recent changes | Switch to MediaWiki mode

Printable version | Disclaimers | Privacy policy | Current revision
Category: Fuel System

Revision as of 07:09, 3 March 2009
Ddgonzal (Talk | contribs)
(->Fuel Sender)
<- Previous diff
Revision as of 04:47, 20 March 2009
Ddgonzal (Talk | contribs)

Next diff ->
Line 95: Line 95:
The fuel return line services to return a part of the fuel to the fuel tank to suit different engine operating requirements, preventing the possibility of fuel heated flowing through the fuel line inside the engine compartment, and elminating "percolation" inside the carburetor.<hr></blockquote> The fuel return line services to return a part of the fuel to the fuel tank to suit different engine operating requirements, preventing the possibility of fuel heated flowing through the fuel line inside the engine compartment, and elminating "percolation" inside the carburetor.<hr></blockquote>
 +
 +
 += Venting =
 +Datsun 1200 in most parts of the world vents the fuel tank to the atmosphere. A simple hose loop goes from the filler tube up above the tank and back down towards the ground.
 +
 +
 +In USA, the tank is not released directly to the air. Instead, fumes are captured by the Evaporate Emission control (EVAPO) system. For details, see [[Fume Control]].
 +
 +http://datsun1200.com/modules/myalbum/photos/7798.jpg
 +* Fume Control
 +
= Parts Sources = = Parts Sources =

Revision as of 04:47, 20 March 2009

Datsun 1200 uses a 38 or 40 liter petrol tank.

Also see: Fuel Cap, Fuel Gauge, Wiring


Contents

Mounting

Sedan tank is inside boot, just behind rear seat:

  • 3527.jpg 13984.jpg


Coupe tank is undernearth car, under the boot area:

  • 3528.jpg 2134.jpg


wagon tank

  • 3529.jpg

Capacity

  • Sedan: (40 liter, 10.5 US gal)
  • Coupe: (38 liter, 10 US gal)
  • Wagon: (38 liter, 10 US gal)


Fuel Sender

The fuel level 'sender' is the sensor in the tank.

  • Sedan sender
    13983.jpg


To remove the sender, only a screwdriver and hammer is needed. Carefully drive the retaining ring anti-clockwise until loose.

19019.jpg

  • Coupe has a vent fitting on it


All use same O-ring and lock plate, including B10 and B120 through B2310:

  • 17342-18000 O-ring
  • 17343-14800 Lock plate (also 17343-14801)


B110 Sedan USA & JDM

  • 25060-H1000 GAUGE-FUEL TANK
  • 25060-H1900 1070-

B110 Coupe USA & JDM

  • 25060-H1800

B110 Van JDM

  • 25060-H1400

B120 JDM

  • 25060-G1000 7510-8111
  • 20560-G1010 8112-

B210 Sedan USA & JDM

  • 25060-H5000

B210 Coupe USA & JDM

  • 25060-H5500
  • 25060-H7210 0974-

B210 Van JDM

  • 25060-H6600

B310 USA Sedan, Coupe, Wagon USA, early JDM

  • 25060-H8500 GAUGE ASSY-FUEL TANK


Wiring

There is a single Yellow wire on the sender. It goes forward to the dash Fuel Gauge. The sender is grounded through the tank body.


See: Wiring - Fuel Gauge


Specifications

As measured by club members, by moving the float up and down from stop to stop:

NOTE: This does not necessarily match "Full" and "Empty" marks of the fuel gauge, due to normal manufacturing tolerances. Typically a 1200 reads well 'E' before it runs out of fuel, this is normal.

Reference: Forum: Fuel sending unit specs


Also see:

Return Line

Starting in 1975, North American B210s were fitted with a fuel return line. Here's what the Nissan publication "Introduction of Datsun B210 (1975 model)" says:


Fuel return system

For preventing abnormal fuel temperature rise, the fuel return system has been installed. In this system, fuel from the fuel tank is delivered to both the carburetor and fuel tank.

The fuel return line services to return a part of the fuel to the fuel tank to suit different engine operating requirements, preventing the possibility of fuel heated flowing through the fuel line inside the engine compartment, and elminating "percolation" inside the carburetor.


Venting

Datsun 1200 in most parts of the world vents the fuel tank to the atmosphere. A simple hose loop goes from the filler tube up above the tank and back down towards the ground.


In USA, the tank is not released directly to the air. Instead, fumes are captured by the Evaporate Emission control (EVAPO) system. For details, see Fume Control.

7798.jpg

  • Fume Control


Parts Sources

  • Nissan. Call Ericksen Nissan's toll-free number. If Ericksen says they can't get a part let us know (click "Edit" and add it to this article). Also, if they do get the part for you, let us know that too!
    • NOTE: Nissan USA is out of stock forever of the Sedan hose. But perhaps they can get the Coupe hose.
  • Wreckers, if you can find a 1200 in a wrecking yard
  • Friends with parts cars
  • Marine supply stores, for general fuel hose and filler hose. NAPA and other old-line auto parts store carry this generic fuel-rated hose also. Trimmed to length using the old filler hose as a guide. It is tough getting it to flex into shape, but can be done.

Filler Hose

Coupe

USA B110 coupe tank

18602.jpg 18603.jpg 18604.jpg 18605.jpg


Sedan

Note that the USA B110 sedan tank uses a 2-piece filler hose (there's a small hose inside the bigger one). This is for the EVAPO (emissions market) vehicles:

9715.jpg
Two-piece curved filler hose for EVAPO system

This hose is NLA (No Longer Available) in US, Canada or Japan. However, the regular single hose can be fitted as follows:

9716.jpg
Straight one-piece filler hose for non-EVAPO system

The hose looks like this:
9717.jpg
Filler Hose Comparo


9718.jpg9719.jpg9720.jpg
Filler Modifications


Discussions:


Photo Index

Sedan Tank factory Baffling:

  • 12328.jpg