Main Menu

Home News Forum Photo Album Tech Wiki Downloads Web Links Polls FAQ Members Map

Fast Search

Slow Search

Google Ad

Revision as of 04:49, 20 March 2009

Datsun 1200 uses a 38 or 40 liter petrol tank.

Also see: Fuel Cap, Fuel Gauge, Wiring

1 Mounting
2 Capacity
3 Fuel Sender
- 3.1 Wiring
- 3.2 Specifications
4 Return Line
5 Venting
6 Parts Sources
7 Filler Hose
- 7.1 Coupe
- 7.2 Sedan
8 Photo Index

Mounting

Sedan tank is inside boot, just behind rear seat:

Coupe tank is undernearth car, under the boot area:

wagon tank

Capacity

Sedan: (40 liter, 10.5 US gal)
Coupe: (38 liter, 10 US gal)
Wagon: (38 liter, 10 US gal)

Fuel Sender

The fuel level 'sender' is the sensor in the tank.

Sedan sender

To remove the sender, only a screwdriver and hammer is needed. Carefully drive the retaining ring anti-clockwise until loose.

Coupe has a vent fitting on it

All use same O-ring and lock plate, including B10 and B120 through B2310:

17342-18000 O-ring
17343-14800 Lock plate (also 17343-14801)

B110 Sedan USA & JDM

25060-H1000 GAUGE-FUEL TANK
25060-H1900 1070-

B110 Coupe USA & JDM

25060-H1800

B110 Van JDM

25060-H1400

B120 JDM

25060-G1000 7510-8111
20560-G1010 8112-

B210 Sedan USA & JDM

25060-H5000

B210 Coupe USA & JDM

25060-H5500
25060-H7210 0974-

B210 Van JDM

25060-H6600

B310 USA Sedan, Coupe, Wagon USA, early JDM

25060-H8500 GAUGE ASSY-FUEL TANK

Wiring

There is a single Yellow wire on the sender. It goes forward to the dash Fuel Gauge. The sender is grounded through the tank body.

See: Wiring - Fuel Gauge

Specifications

As measured by club members, by moving the float up and down from stop to stop:

12 ohms fully up
88 ohms fully down
35 ohms half full (per Nissan Factory Service Manual)

NOTE: This does not necessarily match "Full" and "Empty" marks of the fuel gauge, due to normal manufacturing tolerances. Typically a 1200 reads well 'E' before it runs out of fuel, this is normal.

Reference: Forum: Fuel sending unit specs

Also see:

Fuel Gauge (includes Fuel gauge specs)

Return Line

Starting in 1975, North American B210s were fitted with a fuel return line. Here's what the Nissan publication "Introduction of Datsun B210 (1975 model)" says:

Fuel return system
For preventing abnormal fuel temperature rise, the fuel return system has been installed. In this system, fuel from the fuel tank is delivered to both the carburetor and fuel tank.
The fuel return line services to return a part of the fuel to the fuel tank to suit different engine operating requirements, preventing the possibility of fuel heated flowing through the fuel line inside the engine compartment, and elminating "percolation" inside the carburetor.

Venting

Datsun 1200 in most parts of the world vents the fuel tank to the atmosphere. A simple hose loop goes from the filler tube up above the tank and back down towards the ground.

In USA, the tank is not released directly to the air. Instead, fumes are captured by the Evaporate Emission control (EVAPO) system. For details, see Fume Control.

Fume Control

B210 and newer B120 (Datsun 1200 pickup) adopted the EVAPO system.

Parts Sources

Nissan. Call Ericksen Nissan's toll-free number. If Ericksen says they can't get a part let us know (click "Edit" and add it to this article). Also, if they do get the part for you, let us know that too!
- NOTE: Nissan USA is out of stock forever of the Sedan hose. But perhaps they can get the Coupe hose.
Wreckers, if you can find a 1200 in a wrecking yard
Friends with parts cars
Marine supply stores, for general fuel hose and filler hose. NAPA and other old-line auto parts store carry this generic fuel-rated hose also. Trimmed to length using the old filler hose as a guide. It is tough getting it to flex into shape, but can be done.

Filler Hose

Coupe

USA B110 coupe tank

Sedan

Note that the USA B110 sedan tank uses a 2-piece filler hose (there's a small hose inside the bigger one). This is for the EVAPO (emissions market) vehicles:

Two-piece curved filler hose for EVAPO system