User Login    
 + Register
  • Main navigation
Login
Username:

Password:


Lost Password?

Register now!
Fast Search
Slow Search
Google Ad


[Datsun 1200 encyclopedia]

Ignition Timing

(Difference between revisions)

Datsun 1200 encyclopedia | Recent changes | Switch to MediaWiki mode

Printable version | Disclaimers | Privacy policy | Current revision
Category: Engine Electrical System

Revision as of 07:27, 7 August 2010
ddgonzal (Talk | contribs)
(->Intial Timing Setting)
<- Previous diff
Revision as of 07:28, 7 August 2010
ddgonzal (Talk | contribs)
(->Firing Order)
Next diff ->
Line 35: Line 35:
= Firing Order = = Firing Order =
Almost all inline 4s have a firing order of 1-3-4-2 -- and certainly all Datsun fours. Almost all inline 4s have a firing order of 1-3-4-2 -- and certainly all Datsun fours.
 +
 + NOTE: If the distributor is out of the
 + engine, see [[Installing Distributor]]
First locate #1. First locate #1.

Revision as of 07:28, 7 August 2010

Engine ignition timing (distributor timing) is the foundation of any tune-up. It is generally the first step you need to perform as all other tune-up and carburetor adjustments depend on ignition timing being correct.

If you have the distributor out of the engine, see Installing Distributor.

Contents

Overview

The stock Datsun 1200 distributor orientation
245.jpg
vacuum advance pointing almost straight forward

General Procedure

  • Check the gap on the plugs then put them back in. Spec is 0.028-0.032 for the A12. I recommend 0.035 for the smoothest idle.
  • Set the point-gap or dwell. Use a dwell meter if at all possible as it is much more accurate than the points gap, Set dwell 49 to 55 degrees. If the points are brand new, a feeler gauge can be used to set the gap to 0.018-0.021 in. Incorrect Dwell can cause rough running, as does bad points. For example, it might only run at high idle, and not very smooth at that.
  • Double-check the timing. Spec is 5 degrees for the US A12 and should be safe for any A12 engine. This must be done after setting the dwell -- because changing the dwell affects the timing, but not vice-versa.

724.JPG
730.JPG

NOTE: If you use the older pully with 
the newer cover, then you could get 
really weird timing readings

Ignition Timing Specifications

North America

North America
static timing 5 degrees BTDC
point gap (new points) 0.018-0.021 in
dwell (new or used points) 49-55 degrees
Spark plug gap 0.28-0.32 in

Firing Order

Almost all inline 4s have a firing order of 1-3-4-2 -- and certainly all Datsun fours.

NOTE: If the distributor is out of the 
engine, see Installing Distributor

First locate #1.
22317.jpg
The direction of rotation (Yellow arrow) is always opposite the direction that vacuum advance points (green arrow) -- for all engines, not just Datsuns.

Next, following the direction of rotation (Yellow arrow), count off 1-3-4-2.

Here is the 1974-up distributor:
22318.jpg

1974-up alignment:
22319.jpg

Setting Dwell

If your 1200 still has the factory contact points (if you haven't convereted to Electronic Ignition) you must set the dwell for perfect tune. To accurately check the contact points Dwell angle, use a dwell meter. This is far more accurate than simply setting the points-gap.

From the 1973 Factory Service Manual:

  • Dwell angle: 49-55 degrees
  • Point gap: 0.45 to 0.55 mm (18-22 thousands inch)

NOTE: The same specifications are used for B10, B210 and B310 with contact-point ignition as well.


The gap should be checked every 3,000 miles (5k) as part of a Tune-up.

USA 1972 Owners manual (see page 36 for points-gap details):
00_cover.jpg 36.jpg


Be sure that the contact surfaces are clean and not burned.
The correct gap of 0.018 to 0.022 in (0.45 to 0.55 mm)
should be checked with a feeler gauge.
These days we recommend a dwell meter instead of a feeler gauge. The feeler gauge is fine with new points, but inaccurate with used points due to the pitting/cratering that occurs.

Dwell-Tachometer
20098.jpg
Older style (analog) Dwell-Tachometer

  1. New points are gap-set to 0.018-0.021 inch. In a pinch you can use an old-fashioned matchbook cover, which is typically 20 thousands of an inch thick.
  2. Check the dwell
  3. Readjust the gap until it reads 49-55 degrees

20099.jpg
NOTE: On this type of scale with only 8- and 6-cylinder, 4-cylinder reading is DOUBLE 8-cylinder scale.

Be patient when setting the dwell. You may need to slight re-adust the gap and re-check the dwell many times before it is 'right on'. This involves starting and stopping the engine multiple times. But it will be worth it when your 1200 purrs like a lion.


Intial Timing Setting

  1. turn engine off. Set parking brake. Put transmission in neutral
  2. turn engine by carefully turning fan clockwise, until the timing marks line up (5 degrees BDTC). If the fan belt slips, it's too loose (tighten it!)
    730.JPG
  3. Pull cap off distributor. Is the rotor pointing at the Number 1 spark plug wire? Good. If it is pointing at #4, rotate the engine one more turn until the marks line up again
  4. pull coil wire from cap. Lay atop the engine or strut tower, with the metal lead 1/4 inch from bare metal
  5. turn engine to IGN (do not start it). Distributor cap is removed
  6. Loosen the distributor hold down bolt slightly. Be careful not to rotate the distributor.
  7. Rotate housing clockwise slightly until points appear closed
  8. Rotate housing anti-clockwise -- slowly -- until a spark appears at the coil wire
  9. Tighten distributor hold-down bolt. You are done.

Setting Timing with Timing Light

Fine-tuning the Timing - Relative Timing Marks

Note the timing marks on the A12 plate.

3231.jpg
Advance and Retard marks

These are NOT used to time the engine (the marks on the crankshaft pulley are). But they are very useful for advancing or retarding the timing a degree or two. After installation, you can look down past the #1 spark plug, between the engine and the distributor to view the marks.

  1. Advance it two degrees (turn distributor clockwise), test drive, repeat until it pings at part throttle
  2. Retard it one degree (turn counter-clockwise) to remove the pinging
Once you have this, you can note the crankshaft timing and next time just set it using a Timing Light.

Advanced Timing

Base timing

Tuning for Power

Dialing in Distributor Spark Curve

Mechanical advance

Vacuum advance

Retarding, for boosted engines

Fully electronic spark timing