Main Menu

Home News Forum Photo Album Tech Wiki Downloads Web Links Polls FAQ Members Map

Fast Search

Slow Search

Google Ad

Revision as of 05:02, 20 September 2017

Adorning the extreme ends of the Datsun 1200 are chrome bumpers. Although the front bumper is shared by all models, the rear bumper differs between Coupe, Sedan, Van and Sunny Truck. The revised front bumpers have bolt holes for USA and Japan license plates (two sets of holes), while early ones are specific.

Overview

FRONT
* sedan, coupe, wagon, truck 1971-1978
* truck 1978-2008

REAR
* Sedan  license number lamp
* Coupe  license number cutout
* Wagon  plain straight bumper
* Ute    bumperettes (rubber pads)

Album 21426

OVERRIDERS
Album 21439

SEDAN - straight rear bumper with opening for plate light
Album 25125 Album 25358

Front

The front bumper= of a 1200 is a fairly straight chrome bar and has two small notches on the bottom for the front turn-signal lights:
Album 21425

All 1200 models used the same front bumper, including Truck through March 1978
Album 737 Album 21426 Album 8580 Album 3085 Album 9917 Album 736

North America 1200 came with rubber overriders
Album 10129

The front bumper is in three pieces, although it is sold factory assembled as one piece.

Two long front sections (left and right) that curve and the end to wrap around the side just a little
a shallow degree binding piece (the front bumper is a slight V)

Album 21427

inside

Measurements

Bumper bar
Stay bolt holes: 710 mm apart
Height: ~90 mm
Depth at Center: ~30 mm
Depth off Center: ~45 mm
Has both plate holes:
* License Plate holes USA: 7" (~178mm)
* Number Plate holes Japan 210 mm (some threaded, some not)

Some have extra cosmetic front bolt holes:
Outer front bolt holes: 300 mm outboard of stay holes

Album 24720

Stays

Early vs late stays have a different bolt angle and spacing (not interchangeable).

Early 1200s use 8mm bolts (fastening Stay to Hood Ledge)
08110-81662 BOLT (up to '72-6)

Later 1200s use 12mm bolts
08114-22510 BOLT (from '72-7)

Changed to a longer 30mm long bolt for 1976 JPN (1973 in USA)

Early Front Bumper Stays: 62671-H1001 to June 19792 (8 mm chassis bolts)
Album 21433

Early vs Late stays (notice notch in late version): 62671-H1002 from July 1972 (12 mm chassis bolts)
Album 24909

Stay Measurements

early chassis rail bolt holes: ?
late chassis rail bolt holes: ?

B120

STD utes used a flat-silver painted bumper (62651-G1001). DX utes used a chrome bumper (62651-H1001).

From April 1978, Sunny Truck used a rubber-ended bumper:

Album 20832 Album 20831

Also available in Chrome or Black
Album 21428

New Zealand

Some B120 SportStar utes had black bumpers:
Album 385

B140 Bakkie

The B140 Bakkie has a larger flat bumper, painted black, with lights in the face.
Album 7403

Album 1129 Album 20114

PB110

PB110 Sunny Excellent came with a unique front bumper with a separate bar and S-curved ends. Every piece is different from the 1200 (bar, stays & brackets). The fasteners (bolts, washers and shims) are same as the 1200.

H25 bumper
Album 459

Part Numbers

Bumper end: 62653-H2500 BUMPER-front (R.H.)
Album 26757 Album 26758

Rear

Rear bumpers differ by 1200 model, and are distinguished by the license plate lighting provision. PB110 used the same rear bumpers as regular B110.

#Sedan Rear bumper has a small light in the center facing up to illuminate the license plate
#Coupe Rear bumper has a notch for the license plate:
Album click to view Upload click to view
Wagon is smooth with no notch and no light:
Album click to view Album click to view
#Ute Rear has rear bumper, just rubber pads
Album click to view
North America 1200 had rubber overriders
Album click to view

Alternative bumper on a sedan rear
Album 25713

Sedan Rear

bumper has a small light in the center facing up to illuminate the license plate. PB110 and B110 use same rear bumpers.

Album 11174 Album 20726 Album 2305 Album 20109

Album 25663

Coupe Rear

Coupe bumper has a notch for the number plate, the notch is wide to acommodate Commonwealth plates as well as the narrower Japan plates.

H18 (coupe) bumper bar
Album 225

H19 North America coupe with overriders
Album click to view

Post 476204 Post 476204 Post 476204

Album 3850

Album click to view

Truck Rear

Ute had two small rubber pads (for the tailgate to drop against), and two black corner bumperettes:

Album 2710 Album 5650 Album 237 Album 20967

Album 21431

Custom

Sunny B210 bumper fitted to Sunny Truck]
Album 21423

B140 Bakkie

Late-model B140 Bakkie rear has the standard two black corner bumperettes but with reflectors in the face.

RED starboard
RED port

Starting with the 2003 facelift?]
Album 6427

The latest bakkies had Reflectors in the bumperettes
Album 22424

Album 8986

1973 USA Bumpers

For 1973, USA models got redesigned bumper-to-body brackets to meet FMVSS No. 215 (2.5 mph bumpers). They also used larger bumper pads. The chrome parts look similar but are different.

Post 480921

NOTE: A 1973 front bumper with brackets does not fit a 1971 or 1972 model

Album 15928

H70 front bumper
Album 2029 Album 10906

H70 rear sedan bumper
Album 21440

H71 rear coupe bumper (notched for license plate)
Album 6804 Album 21438

Implementation Details:

Album 6834

Two-piece construction

Note the double-set of bolt holes for the stays (inboard of the lamp cutouts)

License Plate Lighting

 Also see: Rear License Plate Lamp

For North America in order to meet new FMVSS regulations, 1973 Sedan rear bumper was modified to have a brighter license plate lamp (the coupe with its dual lamps was already bright enough). The lighting moved from the bumper to near the plate.

1973 Sedan - bumper bar with no light (H70)
Album 1427