User Login    
 + Register
  • Main navigation
Login
Username:

Password:


Lost Password?

Register now!
Fast Search
Slow Search
Google Ad


[Datsun 1200 encyclopedia]

Camber

(Difference between revisions)

Datsun 1200 encyclopedia | Recent changes | Switch to MediaWiki mode

Printable version | Disclaimers | Privacy policy | Current revision
Category: Suspension Modifications

Revision as of 21:02, 26 April 2016
ddgonzal (Talk | contribs)
(->Move the LCA)
<- Previous diff
Revision as of 21:19, 26 April 2016
ddgonzal (Talk | contribs)
(->Lengthened LCA)
Next diff ->
Line 62: Line 62:
NOTE: B310/Stanza LCA is same length as 1200/120Y/Ute/B310/A10. All the same length. NOTE: B310/Stanza LCA is same length as 1200/120Y/Ute/B310/A10. All the same length.
 +
 +retorally added 20mm
 +<br>[http://datsun1200.com/modules/myalbum/photo.php?lid=21875 http://datsun1200.com/uploads/thumbs/21875.jpg] [http://datsun1200.com/modules/myalbum/photo.php?lid=21876 http://datsun1200.com/uploads/thumbs/21876.jpg] [http://datsun1200.com/modules/myalbum/photo.php?lid=21877 http://datsun1200.com/uploads/thumbs/21877.jpg]
Nissan Competition sold lengthened control arms. See [[Racing_Suspension_System#B310]] Nissan Competition sold lengthened control arms. See [[Racing_Suspension_System#B310]]

Revision as of 21:19, 26 April 2016

Checking camber is part of Alignment for proper tyre wear or to change handling characteristics.

Contents

Overview

The stock 1200 suspension is non-adjustable for Camber. If the camber is out-of-specification, the factory recommends replacing parts. A good suspension man can sometimes bend the strut housing to correct for bad camber.

For upgrading to modern camber settings, there is no provision in the stock parts. Fitting custom adjustable parts is needed.

-VE Camber (Negative camber)

1.5 degrees negative camber can work well for racing or spirited driving. Large amounts of -VE are mainly for looks -- for performance you want the tread parallel to the pavement. But since the car leans in corners, having some negative camber keeps the tire tread parallel to the pavement even when leaning.

Front

Datsun 1200 is designed with non-adjustable front suspension, so a simple Wheel alignment will not change the camber angle.

-VE can be achieved in the front suspension with either method:

  • Move the top of the strut. Slot the strut-top mounting points per the Nissan Competition suspension manual
  • Use adjustable Camber Tops

Alternatively, following methods increase the track, which may interfere with wide tyres and/or require flares

  • Move the LCA mounting point in the crossmember
  • Use a lengthened LCA, like the Nissan Competition units
  • use a longer Ball Joint

As always after modifying the front suspension, the Toe-in must be re-adjusted to retain correct wheel alignment.

Move the Strut Top

Slot the strut-top mounting points per the Nissan Competition suspension manual
352.jpg355.jpg
discussion
22690.jpg 22691.jpg

N13/N14 strut tops
22689.jpg

Camber Tops

Install Aftermarket adjustable strut tops, which are adustable in the camber direction.

See main article: Camber Tops


adjustable strut tops ... only helps to get a little bit more camber and/or castor. To get [a large amount of] camber, you need to run smaller diameter springs, as well as the adjustable strut tops. With the standard springs, the available adjustment will be restricted inside the strut tower by the large original spring diameter.

Small coilover type springs and adjustable strut tops are good for about 4.5 degree negative camber.

Move the LCA

Redrill or slot the crossmember mounting points for the LCA -- moving it outwards gain negative camber.

full

album

album

K-MAC camber kit
22825.jpg

Lengthened LCA

Use longer bottom arm. Or lengthen the arm, like this:
album

NOTE: B310/Stanza LCA is same length as 1200/120Y/Ute/B310/A10. All the same length.

retorally added 20mm
21875.jpg 21876.jpg 21877.jpg

Nissan Competition sold lengthened control arms. See Racing_Suspension_System#B310

Longer Ball Joint

Another way to push the bottom of the tyres out is to use a longer Ball Joint. The A10 and some B310 models use a longer ball joint which fixes the bottom of the strut further outboard (more neg. camber).

See main article: W50 Ball Joint

7978.jpg

Rear Axle

Negative camber can be achieved with the straight axles by cutting and welding.

This axle has 2.5 degrees negative camber with reportedly no problem over three years of driving.
Discussion: 2.5 degree camber rear axle