810 Brakes

Revision as of 01:28, 20 February 2014; view current revision
<-Older revision | Newer revision->

Datsun model series 810 was produced 1976-1979. In some countries it was marketed as "Bluebird", in others as "200B" or "180B" or "160B" depending on the engine fitted.

Overview =

810 rotors are solid discs. Vented discs like the 280ZX swap are superior for fade-resistant, which is important for racing and for mountain driving.

NOTE: For the Japan market 810, front drum brakes were used for Van Deluxe, and for all LPG models (810.P with L18P engine, 811.P with Z18P engine).

245 mm

4-cylinder 810s used same 245 mm brake rotors as B310 Sunny. Most 810 SSS used this too.

Annette 20, N20 (AN20) Type

40207
40206-U6700 Annette N20 (AN20) 245 mm rotor
* Short Body, except SSS ES model
Also from:
* A10 (Stanza)
* B210 A14
* B310 A14/A15

See B310 Strut Swap and Stanza Strut Swap

253 MM

Annette 22 N22 (AN22) Type

253.5 (254) mm 40206-U7600 
* Long Nose models (including 4-cylinder) except EF and EL
* SSS ES model
* 200SX USA S110 1980-1983
* Centric 121.42015
Height: 47.6 mm
Thickness new: 12.5 mm
Thickness min: 11.5 mm
weight 4.7 kg
4 x 95mm bolt circle

Caliper 

Pad Kit 41000K
41060-U2726/41060-U2727
41060-U3426

257 MM

257 mm
* 200B Australia early?
* 180B Europe
Thickness: 26 mm
Height: 52.2 mm
Minimum thickness: 24 mm
Centering diameter: 68 mm
5-bolt
* 40206-9C100/40206-9C101, 40206-Y9502
* Ferodo DDF722

270 MM

N34 type was used G6EL and G6EF (EFI) six-cylinder 810s, and all North American 810s.

270 mm (10.62 inch) 
Nissan part number 40206-U8700
* C230 Nissan Laurel
* G810 L24 or L20
* Japan: Bluebird 2000G6 2 liter [L20S, L20E]
Height 48 mm
Nominal thickness 12.5 mm
Min thickness 10.5 mm
Hub hole: 73 mm
Bolt circle: 4 x 95 mm (to hub)
Type: Bolts behind the hub (same as Datsun 1200)
Weight: 13.7 lbs (compare to 1200 at 5.9 lbs)
* Centric 121.42009
* Aimco 3127
* Wagner BD97318
* Raybestos 9252R/9252

270mm discs use Annette 34 calipers
* dual-piston sliding yoke (same as Datsun 1200 but larger)
* Bore: 54 mm (2.12 inch)
* Pad: 10x .01140
41000-U8700 AN34 caliper, RH
41010-U8700 AN34 caliper, LH
* Centric 141.42010,141.42009
* Raybestos FRC3030, FRC3029
* Beck/Arnley 0760056
* Wagner CR105925
Also fits
 Caliper with yoke:
 * 200SX S110 1980-1983
 Caliper w/o yoke:
 * 620 1978-1979
 * 720 1980-1983 to 11/82

Brake pads for 270 mm
Pad Kit 41000K
41060-U8725
77.7 x 69.2 x 15.5 mm
FMSI TYPE: D57, D114, D161, D173, D238, D244, D246
* Centric 102.01140
* Beck/Arnley 0861175, 0821175 
* 41060-B9525/41060-B9527 Datsun 720 USA
* 41060-E4125
* 41060-N3026, 41060-N3036, 41060-N4426, 41060-N8525
* 41060-U8725