User Login    
 + Register
  • Main navigation
Login
Username:

Password:


Lost Password?

Register now!
Fast Search
Slow Search
Google Ad


[Datsun 1200 encyclopedia]

Dellorto

(Difference between revisions)

Datsun 1200 encyclopedia | Recent changes | Switch to MediaWiki mode

Printable version | Disclaimers | Privacy policy | Current revision
Categories: Engine Modifications | Fuel System

Revision as of 05:58, 29 January 2016
ddgonzal (Talk | contribs)
(->Adjustment)
<- Previous diff
Revision as of 01:08, 25 February 2016
ddgonzal (Talk | contribs)
(->Overview)
Next diff ->
Line 3: Line 3:
Dell'Orto carburetors from Italy their DLHA series were fitted to the Datsun 1200 [[SSS]] model. Dellorto made other types, but the DHLA fit the common [[Weber DCOE carburetor]] intake manifolds. Dell'Orto carburetors from Italy their DLHA series were fitted to the Datsun 1200 [[SSS]] model. Dellorto made other types, but the DHLA fit the common [[Weber DCOE carburetor]] intake manifolds.
 +
 += Also See =
 + * [[Choosing A Carburetor]]
= Overview = = Overview =
Line 16: Line 19:
The last Dellortos were made for the Lotus Esprit Turbo. Production ceased in 1992 due to lowered demand for carburetors in the face of EFI. The last Dellortos were made for the Lotus Esprit Turbo. Production ceased in 1992 due to lowered demand for carburetors in the face of EFI.
 +
 +The great thing about these carbs is that the jets are externally accessible, even when the air filter is on. This makes jet changes at the racetrack a snap.
 +
 +Dellorto DHLA uses the same Intake Manifold as [[Weber DCOE carburetor]], or [[Mikuni PHH]].
 +
 += Single Or Twin =
 +A twin setup has a huge advantage over the single: ITB (individual throttle bores). 2 sidedrafts = 4 throttles.
 +
 + See [[Choosing_A_Carburetor#Single_or_Twin.3F|Choosing A Carburetor: Single or Twin?]]
 +
 +{{Sidedraft}}
= Source = = Source =

Revision as of 01:08, 25 February 2016


Dell'Orto carburetors from Italy their DLHA series were fitted to the Datsun 1200 SSS model. Dellorto made other types, but the DHLA fit the common Weber DCOE carburetor intake manifolds.

Contents

Also See

* Choosing A Carburetor

Overview

5468.jpg

Dellorto DHLA are similar to the Weber DCOE carburetors, but have their own unique parts and some say a better design and look better.

http://www.dellorto.com


The DHLA & DRLA carburettors are widely believed to be the most sophisticated carburettors of their type, prompting David Vizzard to say in Auto Performance magazine, “Dell’Ortos produce truly excellent results...On engines where atomisation is a premium requirement, Dell’Ortos are superior to everything”.

174_4de174af193c2.jpg

The last Dellortos were made for the Lotus Esprit Turbo. Production ceased in 1992 due to lowered demand for carburetors in the face of EFI.

The great thing about these carbs is that the jets are externally accessible, even when the air filter is on. This makes jet changes at the racetrack a snap.

Dellorto DHLA uses the same Intake Manifold as Weber DCOE carburetor, or Mikuni PHH.

Single Or Twin

A twin setup has a huge advantage over the single: ITB (individual throttle bores). 2 sidedrafts = 4 throttles.

See Choosing A Carburetor: Single or Twin?

Intake Manifold

Weber DCOE, Dellorto DHLA and Mikuni/Solex PHH use the same manifolds. Single or Twin manifolds are available, for round-port or oval-port A-series engines.


Vacuum Connection

Drill & tap the boss for a tube fitting. Can be used for power brakes, distributor vacuum advance.

14778.jpgAlbum 14778

Air Filter

Many use simple screens over the carburetor, which keep large objects out of the engine. This (or no screen) provides the fullest "awesome sidedraft sound", but at the expense of increased engine wear.

For filtering, the easiest thing is sock filters, but all sorts of regular and remote filter can be used.

7766.jpg 24885.jpg

LHD Fitment

Space for twin sidedrafts on LHD 1200s is limited because the brake master cylinder is on the carburetor side of the engine.


Heat Shield

Carb heat plate キャブ ヒート プレート
25550.jpgAlbum 25550

Adjustment

Idle Speed and Mixture Adjustment

  1. Warm engine fully
  2. Adjust curb idle speed to 900 rpm
  3. Slowly turn mixture screw out until the engine speeds up, then keep turning out until engine starts to slow down slightly (overly rich)
  4. Screw in (clockwise) until engine slows down (lean). Turn back out til it runs fastest (Best Lean)
  5. Repeat for second barrel of the carburetor
  6. If a twin-carb setup, repeat for the second carburetor

To get a 'feel' for this adjustment, turn the screw by half turns clockwise and anticlockwise till you hear the engine speed up and slow down. Then fine turn with 1/4 turns. Do this repeatedly until you are confident of the results.

Linkage

5212.jpgAlbum 5212 9863.jpgAlbum 9863

Linkage depends in part on the manifold you use. Does it have bolt-bosses for linkage? Or does it have built-in linkage bar?

Side Pull

Tomei manifold Side Pull. Nismo/Tomei manifold have built-in bar towers and use a large diameter cross bar
8988.jpgAlbum 8988

Center Pull

Center Pull - Need the floating lever for the carburetors. In essence, a single throttle lever, with its own balance screw
dcoe_linckage.gif

Center Pull needs only one carb-pull, eliminating the separate throttle adjustments. The center floating linka has its own balance screw
15692.jpgAlbum 15692 15691.jpgAlbum 15691

Single Carb Linkage

For bolt-style manifolds
20641.jpgAlbum 20641

Quadrant

Fan lever - Harada Shosho company
27290.jpgAlbum 27290

Nissan cable quadrant
11496.jpgAlbum 11496 11497.jpgAlbum 11497 11368.jpgAlbum 11368

Generic cable bracket
11506.jpgAlbum 11506

Throttle Lever

Universal carby throttle lever
556.gifAlbum 556

Source

Dellorto DHLA may be purchased from Eurocarb at http://www.dellorto.com

Selection

As with any carburetor, the single most important specification is the venturi (choke) size -- not the barrell size. So a 40 or 45 is not the question. The question is which choke size should be used.

See main article: Carburetor Sizing

For a stock A12, 28 mm is the correct choke size. Which the DHLA series, you can use either 40s or 45s -- a wide variety of venturis are available for both.

Adjustment

Idle Speed and Mixture Adjustment

  1. Warm engine fully
  2. Adjust curb idle speed to 750 rpm
  3. Slowly turn mixture screw out until the engine speeds up, then starts to slow down
  4. Screw in (clockwise) to lean the mixture down to 725 rpm

Do the same for both carburetors. To get a 'feel' for this adjustment, turn the screw by half turns clockwise and anticlockwise till you hear the engine speed up and slow down. Then fine turn with 1/4 turns. Do this repeatedly until you are confident of the results.

Tuning

Tuning any carburetor is mythically difficult. However, DHLA is no more complicated than Weber or the Hitachis that come stock on Datsuns. They are tuned basically the same way.

SSS DHLA40 jetting specs
Venturi: 28mm
Main jet: 115
Needle and seat: 1.50
Float: .01
Starter jet: 70
Starter emulsion tube: .01
Idle jet holder: .01
Idle jet: 50
Air corrector: 200
Emulsion tube: .01
Aux venturi: .01
Pump jet: 33
Pump delivery: 7.5

To suit SSS A12 engine with mild rally cam (see specs in SSS section) and 4-2-1 tubular headers

Also see: http://www.gruntled.com/Dellorto/

NOTE: When removing and re-inserting the Pump Jet, be sure to line up the passages. See http://www.gruntled.com/Dellorto/PumpJet.html

  1. Choose DHLA 40 for A-series engines
    1. Or DHLA 45 for larger engines
  2. Choose appropriate venturi size, perhaps 26mm is best for stock A12 engine
    • Available from 25 mm to 37 mm in increments of 1mm
    • Part number 8383.25 to 8383.37 at Eurocarb
    1. Auxiliary venturi from size 1 to 4
  3. DHLA Starter -- tuning for cold starting
    1. starter jet sizes from 48 (3315.48) to 105 (3315.105)
    2. starter emulsion tube 1 to 4 (7482.1 to 7482.4)
  4. Accelerator Pump
    1. Pump Jet sizes 33 to 60
    2. Pump rod adjustment. Screwing the nut tighter increases fuel delivery, turning it anti-clockwise reduces delivery.
      • Combination of Jet and tightness works 1) Time, shoot for 1 second 2) volume. Probably twin carbs will be within 1/2 turn of each other to deliver the same volume. Test this by actual measurement using a CC vial.