Revision as of 20:33, 14 July 2015

The stock rear brakes are fairly good, a large (for such a light car) 8" x 1.75 brake shoe. Make sure the brakes and clean and adjusted correctly every 3 months. Using a performance pad will improve it.

But for coolness sake... read on.

1 H145
2 H165
- 2.1 Sentra Rotor Adaption
- 2.2 Factory Disc Adapters
  - 2.2.1 Disc Over Drum
  - 2.2.2 910
    - 2.2.2.1 Narrow Pattern
    - 2.2.2.2 Wide Pattern
3 Rear Axle Swaps
- 3.1 Mad Dat Kit

H145

Pitroad Kit

Pitroad rear disc adapters for B110

Uses late model S130 (280ZX) caliper and rotor (I think it says it uses Skyline HR30 adapters)

44155-N3202 machined with:
* 4 new holes for the H145 pattern
* an insert for the smaller diameter axle tube interface

Andy: The Pitroad rear disk brake kit only includes the brackets, E-brake cables, axle sleeve thingys, clips, rubber brake hoses, and axle bolts. You supply the calipers, pads, and rotors from an 82-83 280ZX, as well as new oil seals for the axles, wheel bearings, etc. It's pretty straight forward, you have to pull off the old drum brake assemblies and put on their new bracket just before you put the new wheel bearings in. You do have to drill two really small holes on the E brake cable holder, but other than that it's really easy.

In general, 1982 280ZX and 300ZX has a smaller rear caliper with larger pads than the early (1979-1981) 280ZX. The offset of the early vs. late caliper is quite different.

R31 Australia

You can fit the Australian-built R31 Pintara/Skyline disc brakes onto H145/H150 axle.

See main article: R31 Rear Disc Brake Swap

AE86

To fit AE86 calipers on B110 rear axle housing, create an adapter.

H165

Sentra Rotor Adaption

[1]

Moar Piccies! See 3rotor's gallery

Factory Disc Adapters

Fits H165 and H190 rear axle assemblies, like the 1200 Ute axle assembly.

Disc Over Drum

"Disc Over Drum" -- easy conversion for H165 or H190 diffs! Fits over 14" wheels. Rotor approximately 280mm. Find an Australia-built Bluebird with rear discs and swap the brakes over to the H165.

See main article: Disc Over Drum

910

910 Sedan (810/Maxima/Bluebird) use a conversion plate to bolt a rotor to drum-brake-spec hub.

Narrow Pattern

44155-N3202 ADAPTER-CALIPER 44165 $72 USD
* yoke type/double piston (wide bolt pattern)
* USA 910 1981 (0780-0681) sedan Datsun 810/Maxima IRS
* JPN F30 8009-8208 L28E Leopard/TR-X
          8009-8107 L20E#
Stock Use:
 44151 BAFFLE-PLATE
  44151-U7800 0780-0681
 44001 CALIPER ASSY-REAR RH,W/O PADS OR SHIMS [or yoke]
  44001-F5490 0780-0681 <2> 44001-W1390
240Z use: use early 280ZX caliper & rotor
1200 use: same as 240Z?

 fullsize

Wide Pattern

Use the same install method as the Pitroad adapters (above). The Pitroad units appear to be 44155-N3202 machined with 4 new holes for the H145 pattern, and an insert for the smaller diameter axle tube interface.

fullsize

44155-04S10 ADAPTER-CALIPER 44165
* single piston type (narrow bolt pattern)
* USA 910 1982-1984 (0781-) sedan 810/Maxima
* JPN C31 8111- GX#+K.L20.MD Laurel
* JPN F30 8108- L20E#
* JPN R30 8108-8108 L20ET Skyline
Stock Use:
 44151 BAFFLE-PLATE
  44151-04S10 0781-0683 <> 44151-04S70
  44151-04S60 0783- 
  44151-04S70
44001 CALIPER ASSY-REAR RH,W/O PADS OR SHIMS 
  44001-04S90 0781- <2> D4001-04S90
240Z use: use late 280ZX caliper & rotor
  
1200 use: 1982-1983 280ZX (Late ZX) caliper & Rotor